Máy Photocopy Canon iR 2520w

Máy Photocopy kỹ thuật số, Laser trắng đen

Chức năng: Copy + In mạng + Scan màu qua mạng

Bộ nạp và đảo mặt bản gốc : có sẵn

Bộ tự động đảo 2 mặt bản sao : có sẵn

Khổ giấy sao chụp tối đa : A3

Tốc độ sao chụp/ in : 20 bản/phút

Code: E000-0001
Description:Fixing temperature abnormal rise
The temperature detected by the main thermistor does not rise to the specified value during startup control.
Remedy:1.Go through the following to clear the error: CLEAR > ENGIN > ERRCLR; and then turn OFF and then ON the power. 2.Check connection of the Connectors (Thermistor Connector and AC Connector). 3.Replace the Fixing Main Thermistor (Film Unit). 4.Replace the Fixing Assembly. 5.Replace the DC Controller PCB (PCB4).

Code: E001-0000
Description:Fixing unit temperature rise detection
The reading of the main thermistor is 250 deg C or more continuously for 200 msec.
Remedy:1.Go through the following to clear the error: CLEAR > ENGIN > ERRCLR; and then turn OFF and then ON the power. 2.Check connection of the Connectors (Thermistor Connector and AC Connector). 3.Replace the Fixing Main Thermistor (Film Unit). 4.Replace the Fixing Assembly. 5.Replace the DC Controller PCB (PCB4).

Code: E001-0001
Description:Fixing unit temperature rise detection
The hardware circuit detects overheating of the main or sub thermistor for 200 msec.
Remedy:1.Go through the following to clear the error: CLEAR > ENGIN > ERRCLR; and then turn OFF and then ON the power. 2.Replace the DC Controller PCB (PCB4).

Code: E001-0002
Description:Fixing unit temperature rise detection
The reading of the sub thermistor is 295 deg C or more continuously for 200 msec.
Remedy:1.Go through the following to clear the error: CLEAR > ENGIN > ERRCLR; and then turn OFF and then ON the power. 2.Check connection of the Connectors (Thermistor Connector and AC Connector). 3.Replace the Fixing Main Thermistor (Film Unit). 4.Replace the Fixing Assembly. 5.Replace the DC Controller PCB (PCB4).

Code: E002-0000
Description:Fixing unit temperature insufficient rise
1.The reading of the main thermistor is less than 115 deg C continuously for 400 msec 1.3 sec after it has indicated 100 deg C. 2.The reading of the main thermistor is less than 150 deg C continuously for 400 msec 1.3 sec after it has indicated 140 deg C.
Remedy:1.Go through the following to clear the error: CLEAR > ENGIN > ERRCLR; and then turn OFF and then ON the power. 2.Check connection of the Connectors (Thermistor Connector and AC Connector). 3.Replace the Fixing Main Thermistor (Film Unit). 4.Replace the Fixing Assembly. 5.Replace the DC Controller PCB (PCB4).

Code: E003-0000
Description:Low fixing temperature detection after standby
The reading of the main thermistor is less than 140 deg C continuously for 400 msec or more.
Remedy:1.Go through the following to clear the error: CLEAR > ENGIN > ERRCLR; and then turn OFF and then ON the power. 2.Check connection of the Connectors (Thermistor Connector and AC Connector). 3.Replace the Fixing Main Thermistor (Film Unit). 4.Replace the Fixing Assembly. 5.Replace the DC Controller PCB (PCB4).

Code: E004-0000
Description:Thermistor disconnection detection error
When disconnection is detected with connector (J214) for 30 sec continuously.
Remedy:1.Check connection of the Connector (J214). 2.Replace the Film Unit. 3.Replace the Fixing Assembly. 4.Replace the DC Controller PCB (PCB4).

Code: E010-0001
Description:Unstable rotation of the Main Motor (M1)
Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec.
Remedy:1.Replace the Main Motor (M1). 2.Replace the DC Controller PCB (PCB4).

Code: E010-0002
Description:Unstable rotation of the Main Motor (M1)
During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence.
Remedy:1.Replace the Main Motor (M1). 2.Replace the DC Controller PCB (PCB4).

Code: E014-0001
Description:Unstable rotation of the Fixing Motor (M2)
Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec.
Remedy:1.Replace the Fixing Motor (M2). 2.Replace the DC Controller PCB (PCB4).

Code: E014-0002
Description:Unstable rotation of the Fixing Motor (M2)
During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence.
Remedy:1.Replace the Fixing Motor (M2). 2.Replace the DC Controller PCB (PCB4).

Code: E019-0000
Description:Error in Waste Toner Sensor (S17)
Warning when the sensor goes on for 2000 consecutive sheets, and error when the sensor goes on for 100 consecutive sheets.
* Error occurs after the delivery if a paper in passage exists.
Remedy:1.Replace the Waste Toner Sensor (S17). 2.Replace the DC Controller PCB (PCB4).

Code: E020-0000
Description:The path between the sub hopper and the developing assembly is clogged with toner.
The Developing Assembly Toner Sensor (TS1) detects the absence of toner,while the Sub Hopper Toner Sensor (TS2) detects the presence of toner. With the Developing Cylinder Clutch (CL3) turned on, the hopper feedscrew motor (M7) is rotated for 1 sec intermittently 194 times; still, theDeveloping Assembly Toner Sensor (TS1) does not detect the presence of toner.
* Error occurs after the delivery if a paper in passage exists.
Remedy:1.Check the rotation of hopper motor gear. (If rotating, false detection by the sensor is doubted. Feed the toner to the developing unit in service mode: CLEAR>ENGIN>TNRINST.) 2.Replace the Developing Assembly Toner Sensor (TS1). 3.Replace the Sub Hopper Toner Sensor (TS2). 4.Replace the DC Controller PCB (PCB4).

Code: E024-0000
Description:The connector (J207) of Developing Assembly Toner Sensor (TS1) is disconnected.
The Developing Assembly Toner Sensor (TS1) connection detection signal is absent for 100 msec 10 times in sequence. * Error occurs after the delivery if a paper in passage exists.
Remedy:1.Check connection of the Connector (J207). 2.Replace the Developing Assembly Toner Sensor (TS1). 3.Replace the DC Controller PCB (PCB4).

Code: E024-0001
Description:The Developing Assembly Toner Sensor (TS1) is disconnected
<At LOW SPEED> - The developing assembly toner sensor (TS1) ON counter is checked every 2.5 seconds, and the counter increments 1 count every 25 times when the sensor goes on, and 300 counts are reached.
<At HIGH SPEED> - The developing assembly toner sensor (TS1) ON counter is checked every 1.5 seconds, and the counter increments 1 count every 15 times when the sensor goes on, and 300 counts are reached.
Remedy:1.Check connection of the Connector (J207). 2.Correct the cable. 3.Replace the Developing Assembly Toner Sensor (TS1).

Code: E025-0000
Description:The connector (J207) of Sub Hopper Toner Sensor (TS2) is disconnected.
The Sub Hopper Toner Sensor (TS2) connection detection signal is absent for 100 msec 10 times in sequence.
* Error occurs after the delivery if a paper in passage exists.
Remedy:1.Check connection of the Connector (J207). 2.Replace the Sub Hopper Toner Sensor (TS2). 3.Replace the DC Controller PCB (PCB4).

Code: E025-0001
Description:Failure of the Bottle Motor (M6)
The bottle motor (M6) is unlocked when it goes on for 12 consecutive times at 0.1 sec. intervals.
* Error occurs after the delivery if a paper in passage exists.
Remedy:1.Replace the Bottle Motor (M6). 2.Replace the DC Controller PCB (PCB4).

Code: E110-0001
Description:Failure of the Scanner Motor (M21)
The Scanner Motor (M21) speed lock signal does not indicate a locked state a specific period of time after the Scanner Motor (M21) has been started.
* The same condition is detected after the error retry is performed.
Remedy:1.Check the cable. 2.Replace the Laser Scanner Unit. 3.Replace the DC Controller PCB (PCB4).

Code: E110-0002
Description:Failure of the Scanner Motor (M21)
The speed lock signal indicates a deviation 10 times in sequence at intervals of 100 msec after the signal has indicated a locked state.
* The same condition is detected after the error retry is performed.
Remedy:1.Check the cable. 2.Replace the Laser Scanner Unit. 3.Replace the DC Controller PCB (PCB4).

Code: E110-0003
Description:Failure of the Scanner Motor (M21)
The scanner motor (M21) speed lock signal does not indicate a locked state for 6.5 sec. after a switchover is made from low to normal speed or for 8 sec. after a switchover is made from normal to low speed.
* The same condition is detected after the error retry is performed.
Remedy:1.Check the cable. 2.Replace the Laser Scanner Unit. 3.Replace the DC Controller PCB (PCB4).

Code: E196-0000
Description:Error in EEPROM access
20 retries failed after error occurred during communication with EEPROM.
* Error occurs after the delivery if a paper in passage exists.
Remedy:1.Replace the DC Controller PCB (PCB4).

Code: E197-0000
Description:Error in communication of Laser Driver PCB (PCB14)
Communication error 1 with image PCB
Remedy:1.Check the cable. 2.Replace the Laser Scanner Unit. 3.Replace the DC Controller PCB (PCB4).

Code: E197-0001
Description:Error in communication of Laser Driver PCB (PCB14)
Communication error 2 with image PCB
Remedy:1.Check the cable. 2.Replace the Laser Scanner Unit. 3.Replace the DC Controller PCB (PCB4).

Code: E202-0000
Description:There is an error in the detection of the CIS home position.
1.The attempt to detect the home position fails when the CIS is moved forward.
2.The attempt to detect the home position fails when the CIS is moved back.
Remedy:1.Disconnect and then connect the flexible cable(Relay PCB (PCB2)-Main Controller PCB (PCB1) 64pin). 2.Replace the flexible cable. 3.Replace the CIS HP sensor (S31). 4.Replace the Scanner Motor (M31). 5.Replace the Relay PCB (PCB2). 6.Replace the Main Controller PCB (PCB1).

Code: E240-0000
Description:Error in controller communication
The serial communication error such as parity error or overrun error is constantly detected.
Remedy:1.Check the Connectors. 2.Replace the DC Controller PCB (PCB4).

Code: E240-0001
Description:Error in controller communication
The serial communication error such as parity error or overrun error is detected while printing.
Remedy:1.Check the Connectors. 2.Replace the DC Controller PCB (PCB4).

Code: E246-0000
Description:Writing to the counter PCB (FRAM) failed
Remedy:

Code: E247-0000
Description:Mismatched checksum between the Flash Rom and the FRAM
Remedy:

Code: E261-0000
Description:Error in Zero Cross
Zero Cross failed to be detected for 500ms or more while the relay was ON.
* The same condition is detected after the error retry is performed.
Remedy:1.Check the Connectors. 2.Replace the DC Controller PCB (PCB4).

Code: E350-0000
Description:SOFT-ID PCB error
Remedy:

Code: E354-0000
Description:Mismatched serial number for the SOFT-ID PCB
Remedy:

Code: E355-0000
Description:Mismatched serial number between the SOFT-ID, the Flash Rom and the FRAM
Remedy:
- Code: E355-0004
- Description:System information error
- Remedy:
- Code: E355-0005
- Description:System information error
- Remedy:
- Code: E500-0000
- Description:Communication error
  The communication with the host machine is interrupted.
- Remedy:1.Check the cable. 2.Replace the Finisher Controller PCB (PCB1). 3.Replace the DC Controller PCB.
- Code: E505-0001
- Description:EEPROM error
  The checksum for the EEPROM data has an error.
- Remedy:1.Replace the Finisher Controller PCB (PCB1).
- Code: E520-0001
- Description:Shift Motor (M4) error
  The shift roller does not leave the shift roller home position when the Shift Motor (M4) has been driven for 1.2 seconds.
- Remedy:1.Replace the Shift Roller HP Sensor (S2). 2.Replace the Shift Motor (M4). 3.Replace the Finisher Controller PCB (PCB1).
- Code: E520-0002
- Description:Shift Motor (M4) error
  The shift roller does not return to the shift roller home position when the Shift Motor (M4) has been driven for 1.2 seconds.
- Remedy:1.Replace the Shift Roller HP Sensor (S2). 2.Replace the Shift Motor (M4). 3.Replace the Finisher Controller PCB (PCB1).
- Code: E531-8001
- Description:Stapler Motor (M10) error
  The stapler does not leave the staple home position when the Staple Motor (M10) has been driven for 0.5 sec.
- Remedy:1.Check the wiring between the Finisher Controller PCB and Stapler. 2.Replace the Stapler. 3.Replace the Finisher Controller PCB (PCB1).
- Code: E531-8002
- Description:Stapler Motor (M10) error
  The stapler does not return to the staple home position when the Stapler Motor (M10) has been driven for 0.5 sec.
- Remedy:1.Check the wiring between the Finisher Controller PCB and Stapler. 2.Replace the Stapler. 3.Replace the Finisher Controller PCB (PCB1).

Linh Kiện Máy Photocopy Quang Trung

Máy Photocopy Canon iR 2520w

Máy Photocopy Canon iR 2520w

Mời bạn xem thêm:

Back Top

Chuyên mục